#Leather quiver how to#

Cut it after soaking it.Īfter the middle section of ¾” reed, you’ll transition to the ⅛” round reed once again. Make sure it’s tapered at the ends for a smooth transition.

¾” Flat Reed: This will end up being in the middle of the quiver.

⅛” Round Reed: Weave in another 8 turns of the round reed.

¼” Flat Reed: Do a few circuits with this material after running the ⅛” round reed.

As before, it’s not a bad idea to make sure that you are overlapping separate materials when you make these switches so that everything blends in appearance and is kept secure.

The remaining materials are used to finish off the weaving process. You are encouraged to go around the form 8 times or so before switching to the next material, which will be the ¼” flat reed. At this point, it’s essential to over weave a small section of the round reed with the bamboo-section so that everything blends together. Switch To The ⅛” Round ReedĪt the end of the tapered section of the quiver, it’ll be time to hang materials to the ⅛” round reed. Make sure that each row of bamboo is snug with the neighboring rows of bamboo. The bamboo weave should be snug against the quiver, but things shouldn’t be so tight that the shape of the quiver begins to become deformed. Proceed by weaving it over and under the uprights in alternating fashion until the entire form is covered. At this point, you can take it out of the soaking tub and stick it under one of the uprights at the top of the form. The bamboo should’ve been left soaking for a while. Tie the uprights together at the top of the form.Use rubber bands to hold the reeds in place while you weave.A 2×2 in a vise works well for these purposes. It’ll be helpful if you can place the PVC form in a vice to keep things from moving out of place.It requires a fair bit of craftsmanship, although it is certainly not impossible to do if you follow the steps in the section below. Perhaps the most challenging part of the process is the weaving of the bamboo through the upright reeds. You could use any similarly-sized object to help form the basket, but you will need to use a rigid object to help form the quiver. This will be used to form the shape of the quiver. Always make sure the reeds are soaked in water first.įind yourself a 2.5″ diameter Schedule 40 PVC Pipe to make a 3″ diameter quiver.The recommendations for trimming the uprights are simple. Otherwise, it’ll be more challenging to shape them into a basket. The half-oval reed uprights must be trimmed in the center. Be sure to wear gloves throughout the dyeing process.Water-based dyes offer more muted color variations, which can better blend into natural surroundings.Alcohol-based dyes are easier to work with since they don’t bleed through the reeds and dry fast.The type of dye you choose will affect how complex this process will be. Of course, you could probably make a functional quiver without the dye, but the stain makes the quiver look much more presentable. Be creative as you would like, as this is the best opportunity to do so. You don’t have to worry about soaking them for too long. If you let them soak for a while, they will soften and become more malleable. Reeds are very dry and brittle, making them hard to work with at this stage. Whenever you use reeds to form an object, you will need to soak them in water first.

The CTA Basket Quiver instructions ask for 11 uprights of reed, each measuring 25″ in length and ⅜” in diameter. Once you have gathered your materials, remove enough of these from the packaging to fit one quiver. Here are the materials used in these instructions: This set of instructions from the California Traditional Archers calls for Chinese reed and bamboo chair cane (3/16″).

#Leather quiver how to#

Final Thoughts How To Make A Basket Quiverīasket Quivers can be made using the same materials that you would find at a basket-making supplies vendor.Simplest Style-How To Make A PVC Quiver.How To Make A Leather/Faux Leather Back Quiver.